Search Results

Experimentally obtained combustion responses of a typical reverse-tumble wall-controlled direct-injection stratified-charge engine to operating variables are described. During stratified-charge operation, the injection timing, ignition timing, air-fuel ratio, and levels of exhaust gas recirculation (EGR) generally determine the fuel economy and emissions performance of the engine. A detailed heat-release analysis of the experimental cylinder-pressure data was conducted. It was observed that injection and ignition timings determine the thermal efficiency of the engine by controlling primarily the combustion efficiency of the stratified charge. Hence, combustion phasing is determined by a compromise between work-conversion efficiency and combustion efficiency. To reduce nitric-oxide (NOx) emissions, a reduction in overall air-fuel ratio as well as EGR addition is required.

The introduction of the continuously variable transmission (CVT) by General Motors required the introduction of a test to evaluate fluid for the ECOTEC VTi transmission. With assistance from Van Doorne's Transmissie (VDT), the belt and sheave supplier for the transmission, a rig was constructed to test fluids in a transmission-like environment without the variability of in-vehicle testing. The test schedule includes testing for fluid friction coefficient, shear stability, and wear rating and is currently subject to further work aimed at confirming repeatability and discrimination. Once confirmed, the new procedure will become part of the DEX-CVT® specification for the new service fluids for the VT20/25E transmissions.

Condenser, fan, radiator power train cooling module (CFRM) proposed by Delphi Automobile Systems was evaluated in the context of vehicle thermal system analysis. The results from the CFRM configuration were compared with those from the conventional condenser, radiator, and fan power train cooling module (CRFM). The analysis shows that for a typical passenger vehicle, the underhood temperature for the CFRM configuration is more than 10°C lower than its CRFM counterpart when the fan is operating at the same speed of 2500 rpm. This is due mainly to the higher mass flow rate impelled by the fan in the CFRM configuration. At the equal mass flow condition, both the CFRM and the CRFM configurations give similar underhood temperatures; but the fan in the CFRM configuration uses 19% less power, due mainly to the reduction in the fan speed needed to impel the same amount of mass flow rate.

Vehicle requirements are measurable and define the performance of a system and its design constraints. Requirements are developed and translated from the voice of the buying customer, the voice of the government, and the voice of General Motors. Duramax powertrain subsystem requirements are developed from the vehicle requirements. This “flow down” approach optimizes the vehicle as a system. The packaging envelope, common interfaces, and manufacturing impacts were the outcome of the Vehicle Portfolio Development Process. Project execution was a global development process executed by Isuzu Engineers in Japan, Allison Automatic Transmission Engineers in Indianapolis, ZF Manual Transmission Engineers in Detroit, and General Motors Engineers in Detroit.

The International Lubricant Standardization and Approval Committee (ILSAC) ATF subcommittee members have compared the two oxidation bench test methods, Aluminum Beaker Oxidation Test (ABOT) and Indiana Stirring Oxidation Stability Test (ISOT), using a number of factory-fill and service-fill ATFs obtained in Japan and in the US. In many cases, the ATFs were more severely oxidized after the ABOT procedure than after the same duration of the ISOT procedure. The relative severity of these two tests was influenced by the composition of the ATFs. The bench test oxidation data were compared with the transmission and the vehicle oxidation test data.

A roll down methodology has been developed to predict the driver's seat track fore-aft acceleration response using measured half shaft torque time histories and an analytically predicted vehicle sensitivity function suitable for transverse front wheel drive powertrains. The predicted vehicle sensitivity function (a frequency response function) relates the transmission torque applied to the drive axles to the seat track fore-aft acceleration. An experimental procedure was developed to measure the in-situ vehicle sensitivity function. The experimental data was used to correlate the analytical model. The testing results have shown that in the frequency range of the “garage shift” that the vehicle body can be represented as a rigid body. A Nastran model utilizing a rigid body representation of the body and powertrain is used to predict the vehicle response to the torque transient.

Driveline clunk is a phenomenon that can adversely affect customer perception of vehicle quality. Clunk is created by the impact of two driveline components as they oscillate in response to a torque disturbance in the driveline system. This disturbance is typically initiated by a driver controlled engine torque variation, most severely through a throttle or clutch manipulation. This torque variation excites a torsional response from the driveline, manifested by a variety of mechanisms such as resonances of various shafts, housings and axles, clutch oscillations, and gear impacts. Because automotive drivelines are complex systems composed of many rotating components, difficulty arises in identifying the impacts that cause clunk and evaluating the significant parameters that can positively affect these collisions. This paper will describe the application of analysis and test methods in the investigation of clunk in a rear wheel drive, manual transmission vehicle.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

An improvement in a vehicle's front of dash barrier assembly's acoustical performance has in the past been addressed by both adding individual absorbers and increasing the overall weight of the dash sound barrier assembly. Depending upon the target market of the vehicle, adding mass may not be an option for improved acoustical performance. Understanding the value of an increase in vehicle mass and / or cost for a specific level of improved acoustical performance continues to plague both Original Equipment Manufacturer (OEM) Engineers and Purchasing representatives. This paper examines the importance of properly sealing the front of dash pass-through areas and offers recommendations which can improve the overall vehicle acoustical performance without the addition of cost and mass to the vehicle.

Automotive manufacturers have intensified their efforts to increase vehicle fuel economy by reducing weight without sacrificing vehicle size and comfort. Vehicle areas that offer the potential to reduce weight include chassis structural components. A cradle or a subframe is a chassis structural component that is utilized to support the engine/powertrain in front wheel drive vehicles. Traditionally, engine cradles have been manufactured by using stamped steel weldments. Recently, automotive designers are considering alternative processes, i.e., hydro-forming, as well as fabricating engine cradles using lightweight materials. The objective of this paper is to describe the development of an aluminum engine cradle for a General Motors's midsize vehicle. The design criteria and structural performance requirements for this cradle are presented along with an overview of the manufacturing processes used to produce this lightweight structural part.

The wheel force transducer has been proven to be a cost and time effective tool for vehicle load data acquisition and simulation testing. The accuracy of wheel force transducers is typically given in terms of a static calibration, or a quasi-static system generated load case. The actual use of a wheel force transducer often involves high speed rotation, varying camber and steer of the tire on the vehicle, and other dynamic and rim related variations which deviate from the standard laboratory calibration. The Flat-Trac proves to be an excellent tool in the design process and evaluation of the wheel force transducer because it accurately controls and simulates the loading of a rotating wheel assembly. Through Flat-Trac System testing, issues that are critical to the use, accuracy, and integrity of data acquired through a wheel force transducer can be evaluated.

One of the most common applications of planetary (epi-cyclic) gear sets is found in automotive transmissions. A planetary gear set typically total torque applied to be shared by multiple planets making a higher power density possible. This advantage of the planetary gear sets relies heavily on the assumption that each pinion carries an equal share of the total torque applied. However, in production, gear manufacturing and assembly variations along with certain design parameters may prevent equal load sharing among the planets. Here, a generalized mathematical model of a single-stage planetary gear set having n planets is developed to predict load shared by each planet under quasi-static conditions. The model takes into account effects of two most common errors including pinion carrier errors and gear run-out errors. Results of an experimental test program are used to validate the predictions of the model. Generalized guidelines for equal load sharing are also presented.

The new regulations to reduce emissions have resulted in the development of new techniques to maintain or enhance competitive performance. A requirement for the manifold is to help meet the reduction in cold start emissions, particularly during the transient conditions from start to 100 seconds following the Federal Test Procedures for vehicle emissions. Finite element computer models were developed to predict inner and outer wall temperatures, and to determine structural soundness. Tests were performed to assure that noise levels were minimized. Dynamometer lab and field tests were performed to verify that the manifold would meet the design requirements. From the results of these tests and analyses, modifications were made to the weld and manufacturing techniques to improve product life and reduce noise. Dual wall manifolds have proven durability to meet high exhaust gas temperatures up to 1650°F (900°C), while meeting the performance, noise, and weight reduction goals.

General Motors Powertrain Group (GMPTG) has developed an all new small block V8 engine, designated LS1, for introduction into the 1997 Corvette. This engine was designed to meet both customer requirements and competitive challenges while also meeting the ever increasing legislated requirements of emissions and fuel economy. This 5.7L V8 provides increased power and torque while delivering higher fuel economy. In addition, improvements in both QRD and NVH characteristics were made while meeting packaging constraints and achieving significant mass reductions.

General Motors Powertrain Division has developed the next generation big block V8 engine for introduction in the 1996 model year. In addition to meeting tighter emission and on-board diagnostic legislation, this engine evolved to meet both customer requirements and competitive challenges. Starting with the proven dependability of the time tested big block V8, goals were set to substantially increase the power, torque, fuel economy and overall pleaseability of GM's large load capacity gasoline engine. The need for this new engine to meet packaging requirements in many vehicle platforms, both truck and OEM, as well as a requirement for minimal additional heat rejection over the engine being replaced, placed additional constraints on the design.

An automated engine dynamometer test procedure is developed and mathematical models for the main engine control variables are derived from the resulting data base. The new procedure involves sequential testing at many speed/load conditions for various combinations of air fuel ratio, spark timing and exhaust gas recirculation. The total testing time required for generating the data base of more than 2000 test points is less than twelve hours. An independent transient speed/load test is also conducted for the purpose of validating the engine models. The measured and model predicted data are compared for this test which corresponds to a segment of the EPA urban schedule.

Three-way catalysts provide a means of catalytically achieving lower NOx emission levels while maintaining good control of HC and CO emissions. However, very accurate control of air-fuel ratio is necessary. The precise air-fuel ratio control required is accomplished by employing a closed loop fuel metering system in conjunction with an exhaust gas sensor and an electronic control unit. To gain production experience with this type of system, General Motors is introducing it on two 1978 engine families sold in California. One is a 2.5 litre L-4 engine and the other is a 3.8 litre V-6 engine. Closed loop controlled carburetors are used on both systems. This paper discusses these 1978 systems. The components used on both systems are described and emission and fuel economy results are reviewed.

The Experimental Safety Vehicle powertrain and fuel system developed by General Motors in compliance with Contract DOT-OS-00095 with the U.S. Department of Transportation include several special features: a low engine accessory package to meet the front visibility down angle of 8 degrees, engine and transmission mounting for retention at high decelerations, a light aluminum engine, an over-the-rear-axle fuel tank, and a unique evaporative emission fuel pipe routing. A comprehensive test program was planned and final testing to validate contract specifications was conducted.

A comprehensive cycle analysis has been developed for four-stroke spark-ignited engines from which the indicated performance of a single cylinder engine was computed with a reasonable degree of accuracy. The step-wise cycle calculations were made using a digital computer. This analysis took into account mixture composition, dissociation, combustion chamber shape (including spark plug location), flame propagation, heat transfer, piston motion, engine speed, spark advance, manifold pressure and temperature, and exhaust pressure. A correlation between the calculated and experimental performance is reported for one engine at a particular operating point. The calculated pressure-time diagram was in good agreement with the experimental one in many respects. The calculated peak pressure was 10 per cent lower and the thermal efficiency 0.8 per cent higher than the measured values. Thus this calculational procedure represents a significant improvement over constant volume cycle approximations.